Aimed at integrators and developers, the 20-86-5000 series is a small, high specification, POCSAG paging transmitter printed circuit board, inheriting all of the type approvals of the 20-86-9000 Call Point Transmitters range and the 20-86 series Pendant Transmitter range.
PCB Transmitters - UHF
The 20-86-5000 is an extremely small, UHF POCSAG paging transmitter PCB powered by a standard CR2032 coin cell. The transmitter will operate for more than 5000 transmissions under normal conditions before needing to be replaced.
The transmitter is ideal for developers and integrators wishing to develop their own low power solution.
Using a POCSAG receiver the 20-86-5000, as with all paging transmitters, can also be used for any general remote control application, such as turning on lights, disabling alarms or switching machinery on or off.
Care is recommended in order to avoid static discharge which may damage the PCB during handling.
20-86 transmitters support up to 8 inputs, each of which can be programmed with up to a 35-character message. Programming can be either with a serial programming cable that can be purchased separately or pre-programmed when supplied. Once the operating frequency has been set the 20-86-5000 messages can be changed using configuration software with an optional programming lead.
Although the 20-86 is a low power transmitter, a direct line of sight transmission range of up to 200 metres can be expected. Transmit range within buildings is reduced, but still considerable having proven to be effective in some cases between floors and across buildings.
- UHF operation
- Small, light & discrete
- Internal cell battery
- Cost-effective
- Ideal for short distance paging or telemetry applications
- Ideal for developers and integrators
- Capable of operating on existing in-house paging systems
- Simple Telemetry solution
Power Supply | 3V, CR2032 button cell |
Frequency Range | 440-470MHz - UHF |
Frequency Selection | Via Software |
Battery Life | Approx. 5000 transmissions Approx. 5 years standby |
External Power Supply | 3.7 to 18 Volts (via onboard regulator) 3 Volts (unregulated; external battery) |
Power Consumption | Standby: <0.5µA Transmit: 26mA (no TX LED) |
Transmit Power | 10mW |
Channel Spacing | 25kHz, 12.5kHz, or 6.25kHz |
Modulation | FSK with NRZ data |
Deviation | ±4.5kHz, ±2.3kHz, or ±1.0kHz |
Inputs | Eight; user programmable |
Baud Rate | 512, 1200, or 2400 |
Message Format | POCSAG, Alphanumeric or Numeric |
Transmit Duty Cycle | Up to 20%; Maximum 30 seconds on time |
Configuration Application | Sacoto (Salcom Configuration Tool Software) |
Received Indication Outputs | Two LED outputs; via 680Ω resistor |
Transmit Indication Output | TX LED; via 680Ω resistor |
Transmit Duty Cycle | Up to 20%; Maximum 30 seconds on time |
Programming Cable | 20-51-0001 (USB) |
Serial Port | 9600 , N, 8, 1; RS232 |
Antenna | External; connection via thru-hole pad or castellation |
Environmental Protection | None, PCB must be housed in suitable enclosure |
Operating Temperature | 10ºC to +55ºC (+14ºF to +131ºF) |
Weight | 6g with battery |
Board Dimensions | 55.5mm x 32.5mm x 6.5mm (L x W x H) |
Type Approvals | CE, FCC and AS/NZS Pending |
-
Information
The 20-86-5000 is an extremely small, UHF POCSAG paging transmitter PCB powered by a standard CR2032 coin cell. The transmitter will operate for more than 5000 transmissions under normal conditions before needing to be replaced.
The transmitter is ideal for developers and integrators wishing to develop their own low power solution.
Using a POCSAG receiver the 20-86-5000, as with all paging transmitters, can also be used for any general remote control application, such as turning on lights, disabling alarms or switching machinery on or off.
Care is recommended in order to avoid static discharge which may damage the PCB during handling.
20-86 transmitters support up to 8 inputs, each of which can be programmed with up to a 35-character message. Programming can be either with a serial programming cable that can be purchased separately or pre-programmed when supplied. Once the operating frequency has been set the 20-86-5000 messages can be changed using configuration software with an optional programming lead.
Although the 20-86 is a low power transmitter, a direct line of sight transmission range of up to 200 metres can be expected. Transmit range within buildings is reduced, but still considerable having proven to be effective in some cases between floors and across buildings. -
Details
- UHF operation
- Small, light & discrete
- Internal cell battery
- Cost-effective
- Ideal for short distance paging or telemetry applications
- Ideal for developers and integrators
- Capable of operating on existing in-house paging systems
- Simple Telemetry solution
-
Specifications
Specification
Power Supply 3V, CR2032 button cell Frequency Range 440-470MHz - UHF
Frequency Selection Via Software Battery Life Approx. 5000 transmissions
Approx. 5 years standby
External Power Supply 3.7 to 18 Volts (via onboard regulator)
3 Volts (unregulated; external battery)Power Consumption Standby: <0.5µA
Transmit: 26mA (no TX LED)Transmit Power 10mW
Channel Spacing 25kHz, 12.5kHz, or 6.25kHz
Modulation FSK with NRZ data
Deviation ±4.5kHz, ±2.3kHz, or ±1.0kHz Inputs Eight; user programmable Baud Rate 512, 1200, or 2400 Message Format POCSAG, Alphanumeric or Numeric Transmit Duty Cycle Up to 20%; Maximum 30 seconds on time Configuration Application Sacoto (Salcom Configuration Tool Software) Received Indication Outputs Two LED outputs; via 680Ω resistor Transmit Indication Output TX LED; via 680Ω resistor Transmit Duty Cycle Up to 20%; Maximum 30 seconds on time Programming Cable 20-51-0001 (USB) Serial Port 9600 , N, 8, 1; RS232 Antenna External; connection via thru-hole pad or castellation Environmental Protection None, PCB must be housed in suitable enclosure Operating Temperature 10ºC to +55ºC (+14ºF to +131ºF) Weight 6g with battery Board Dimensions 55.5mm x 32.5mm x 6.5mm (L x W x H) Type Approvals CE, FCC and AS/NZS Pending - Manuals & Downloads